A cafetiere (Coffee Plunger, French press in US English) requires coffee of a coarser grind than does a drip brew coffee filter, as finer grounds will seep through the press filter and into the coffee. Coffee is brewed by placing the coffee and water together, stirring it and leaving to brew for a few minutes, then pressing the plunger to trap the coffee grounds at the bottom of the beaker.
There were lots of innovations from France in the late 18th century. With help from Jean-Baptiste de Belloy, the Archbishop of Paris, the idea that coffee should not be boiled gained acceptance. The first modern method for making coffee using a coffee filter—drip brewing—is more than 125 years old, and its design had changed little. The biggin, originating in France ca. 1780, was a two-level pot holding coffee in a cloth sock in an upper compartment into which water was poured, to drain through holes in the bottom of the compartment into the coffee pot below. Coffee was then dispensed from a spout on the side of the pot. The quality of the brewed coffee depended on the size of the grounds - too coarse and the coffee was weak; too fine and the water would not drip the filter. A major problem with this approach was that the taste of the cloth filter - whether cotton, burlap or an old sock - transferred to the taste of the coffee. Around the same time, a French inventor developed the "pumping percolator", in which boiling water in a bottom chamber forces itself up a tube and then trickles (percolates) through the ground coffee back into the bottom chamber. Among other French innovations, Count Rumford, an eccentric American scientist residing in Paris, developed a French Drip Pot with an insulating water jacket to keep the coffee hot. Also, the first metal filter was developed and patented by French inventor.
An electric drip coffee maker can also be referred to as a dripolator. It normally works by admitting water from a cold water reservoir into a flexible hose in the base of the reservoir leading directly to a thin metal tube or heating chamber (usually, of aluminum), where a heating element surrounding the metal tube heats the water. The heated water moves through the machine using the thermosiphon principle. Thermally-induced pressure and the siphoning effect move the heated water through an insulated rubber or vinyl riser hose, into a spray head, and onto the ground coffee, which is contained in a brew basket mounted below the spray head. The coffee passes through a filter and drips down into the carafe. A one-way valve in the tubing prevents water from siphoning back into the reservoir. A thermostat attached to the heating element turns off the heating element as needed to prevent overheating the water in the metal tube (overheating would produce only steam in the supply hose), then turns back on when the water cools below a certain threshold. For a standard 10-12 cup drip coffeemaker, using a more powerful thermostatically-controlled heating element (in terms of wattage produced), can heat increased amounts of water more quickly using larger heating chambers, generally producing higher average water temperatures at the spray head over the entire brewing cycle. This process can be further improved by changing the aluminum construction of most heating chambers to a metal with superior heat transfer qualities, such as copper.
If your busy life keeps you from making coffee by hand, you can also consider a capsule machine such as a Nespresso coffee maker. These machines use small capsules or pods of coffee, so you don’t have to worry about measuring grounds and adding them to your device. Simply add a capsule, fill up the reservoir and press the On button. If you’re more of a traditionalist, a stovetop espresso maker might be the right option for you. This type of maker uses your stove to heat up water, which then steams up and passes through a capsule of grounds above the reservoir. The steamy espresso then collects in an upper reservoir at the top of the maker. These espresso makers are very popular in Europe and require no electricity to function.
All the machines we tested came with either insulated carafes or glass pots with built-in warmers. Both have pros and cons. Glass pots are typically easier to clean because they tend to have wider mouths, and the lack of internal insulation means that glass pots will have a greater interior volume relative to its exterior volume — basically, it’s easier to get your hand or dish sponge into a glass pot. On the other hand, glass pots are more fragile and have to be heated from a base plate. In our tests, those base plates could even raise the temperature of the coffee, like with the CuisinArt, which can make coffee taste burnt.
6 month warranty for Spinn Original, Original Plus, and Original pro. If your machine is defective (DOA) when you receive it, we’ll make it right immediately. For US customers, if it develops a problem later that’s our fault, we’ll either (at our option) ship you the parts that need to be replaced along with detailed instructions, or ship it back to us for repair or replacement – in either case, for free, including shipping. For international customers, parts and repairs are free, but shipping is not included. The warranty covers everything except water filters. Unfortunately, if you modify your firmware, we can’t cover your Spinn under warranty (because it’s easy to break your Spinn by modifying your firmware!)
The built-in burr grinder is high quality, and you can easily adjust the grind size and amount with a dial on the front of the machine. You can choose to use either a single- or double-wall filter basket, and the grinder will automatically adjust to give you the right about of coffee grounds for your brew. Reviewers love that it comes with the grinder and praise its quality.
CR’s take: If you like the look of black stainless steel, you can add a hit of the trendy finish to your kitchen with the Bella Ultimate Elite Collection coffee maker. Appearance aside, this model brews a fresh pot in just 9 minutes and is graceful in action, earning strong ratings in our carafe handling tests. It offers programming, brew-strength control, a pause-and-serve feature, and auto-shutoff. Bella drip machines also received a Very Good rating for predicted reliability. At about $50, this affordable, attractive option won’t disappoint.